1.1875 x 5/16 Inch Neodymium Rare Earth Countersunk Ring Magnets N42 (2 Pack)

1.1875 x 5/16 Inch Neodymium Rare Earth Countersunk Ring Magnets N42 (2 Pack)

1.1875 x 5/16 Inch Neodymium Rare Earth Countersunk Ring Magnets N42 (2 Pack)

  • $ 23.29 USD $23.29


✓ In Stock - Ships Free Within 1 Business Day

Buy More and Save up to 35%
Quantity of Packs Price per Pack Discount
Buy 2 $22.13/pack 5% Off
Buy 3 $20.97/pack 10% Off
Buy 5 $19.80/pack 15% Off
Buy 10 $18.64/pack 20% Off
Buy 25 $17.47/pack 25% Off
Buy 50 $16.31/pack 30% Off
Buy 100 $15.14/pack 35% Off
Need more than 100 packs? Email us for a quote.


Magnet Specifications

Imperial Size 1.1875 x 0.3125 Inch (Outer Diameter x Thickness)
Metric Size 30.162 x 7.937 mm (Outer Diameter x Thickness)
Countersunk Hole Size 0.4 x 0.22 Inches at 82°
Countersunk Hole Location Both Sides (Double Countersunk)
Screw Size #10
Material Grade N42
Pull Force 37.1 lbs
Coating Nickel-Copper-Nickel (Ni-Cu-Ni)
Magnetization Direction Axially
Magnet Material Sintered Neodymium (NdFeB)
Tolerance +/- 0.004 Inches
Max Operating Temperature 80°C / 176°F
Flux Density (Br) 13,300 Gauss
Magnet Weight 41.1 Grams
Part Number DCS1316X516N42-2PK
Quantity Included 2 Countersunk Ring Magnets

Produced in an ISO 9001 Facility
Manufactured to Meet RoHS & REACH Standards



Magnet Safety Warning

Please handle these rare earth 1.1875 x 5/16 inch (Outer Diameter x Thickness) disc magnets with caution. They are incredibly strong and powerful for their small size, and can pose a safety risk.

These grade N42 disc magnets are difficult to separate by hand, and can snap back together with extreme speed and force. This may cause the magnets to break and send small fragments flying into the air, potentially causing injury.

With 37.1 lbs of pull force, these disc magnets can also pinch your fingers if they snap back together. For your safety, keep these magnets far apart and at a safe distance of several feet or more once separated. Hand and eye protection is strongly recommended when handling these magnets.


Installing Countersunk Magnets: Snug, Not Tight

Tighten each screw only until its head sits flush with the magnet, then stop. Neodymium is hard but brittle, so it can't flex like a steel washer. Once the screw head seats, every extra turn wedges it deeper into the countersink and can crack the magnet around the hole.

Use #10 flat-head screws. Avoid pan-head and round-head screws, which press on the thin edge of the hole.

Drive the screw by hand when you can. If you use a drill/driver, set the clutch to a low number, drive slowly, stop about one turn early and finish by hand. Don't use an impact driver or drill mode. Mount the magnet on a flat surface over a pilot hole, because a bump or glue drip underneath can crack it as you tighten.

Learn more:
How Do I Install Countersunk Magnets Without Breaking Them?
Can I Use Metric and Imperial Screws Interchangeably With Countersunk Magnets?

Dimensions are nominal; see the drawing for tolerances. STEP files open in SolidWorks, Fusion, Onshape, FreeCAD and most other CAD software.