How Many Magnets Do I Need to Hold My Item?

Short answer

Add up the listed pull force of all your magnets and aim for at least 1.5× the item’s weight when it pulls straight off the steel, or 7 to 10× when it hangs on a wall and could slide down. Use the higher end of that range on thin steel, such as a fridge door. Any gap between the magnet and the steel cuts the hold further. The calculator below does the math for our most popular N52 discs.

The Rules Behind the Calculator

The listed pull force is measured straight off a thick, flat steel plate with nothing in between (see how pull force is measured). Real projects lose some of that, so we build in these factors:

Situation What it does Factor
Pulls straight off the steel Hanging under a shelf, beam or ceiling Weight × 1.5
Slides along the steel Hanging on a wall, door or the side of a cabinet Weight × 7 to 10
Gap between magnet and steel Paint, fabric, plastic, wood Depends on magnet size

The 1.5× factor is a safety margin for straight pulls. Sliding is much easier than pulling straight off: sideways holding power is only about 15 to 25% of the rating, roughly a fifth, so 5× the weight merely balances the load. Aiming for 7 to 10× adds a safety margin. Use the higher end on thin steel, such as a fridge door or the side of a cabinet.

Using more than one magnet? Divide the total by the number of magnets to get the listed pull force each one needs: a 2 lb tool on a fridge door needs about 20 lb in all, so four magnets need about 5 lb each. Enter the number of magnets in the calculator and it shows which sizes are strong enough. This assumes the magnets share the load evenly, so spread them out and make sure each one sits flat on the steel.

Three ways force is applied: straight pull, pull through a gap, and sliding Straight Pull100% of RatingSSNNPull Through an Air GapDrops QuicklySSNNSliding (Shear)About 15–25%SSNN
Three ways force is applied: straight pull, pull through a gap, and sliding Straight Pull100% of RatingSSNNPull Through an Air GapDrops QuicklySSNNSliding (Shear)About 15–25%SSNNStraight Pull100% of RatingSSNNPull Through an Air GapDrops QuicklySSNNSliding (Shear)About 15–25%SSNNStraight Pull100% of RatingSSNNPull Through an Air GapDrops QuicklySSNNSliding (Shear)About 15–25%SSNN
The same magnet holds much less when the load slides or crosses a gap.

Quick Reference: Total Pull Force to Aim For

If you can’t use the calculator, this table gives the total listed pull force for common weights, with no gap:

Item weight Pulls straight off (1.5×) On a wall (7 to 10×)
1 lb 1.5 lb 7 to 10 lb
2 lb 3 lb 14 to 20 lb
5 lb 7.5 lb 35 to 50 lb
10 lb 15 lb 70 to 100 lb
25 lb 37.5 lb 175 to 250 lb

Worked Examples

A 3 lb Sign Under a Steel Beam

Straight pull: 3 × 1.5 = 4.5 lb. One 3/8 × 1/8 Inch N52 Disc (5.5 lb) covers it.

A 2 lb Tool on a Fridge Door

On a wall, using the high end for thin steel: 2 × 10 = 20 lb. Three 1/2 × 1/8 Inch N52 discs (24.45 lb) or two 3/4 × 1/8 Inch N52 Discs (24.2 lb).

A 10 lb Panel Through Felt

On a wall, through 1/16 in felt: 70 to 100 lb before the gap. A 1 × 1/2 Inch N52 Disc keeps about 55% (30 lb) through the felt, so use three to four.

Tips for a Stronger Hold

  • Spread magnets out. Several magnets spread across an item resist twisting and peeling better than one big magnet in the middle.
  • Keep the gap small. A thin layer costs more than you’d expect; see how air gaps affect strength.
  • Give the magnet a good target. If you control the surface, add a Steel Strike Plate at least as wide as the magnet.
  • Use pot magnets for heavy loads. A Pot Magnet’s steel cup puts more pull on one face and adds a screw or hook.
  • Test before you buy in bulk. Order your best guess and one size up, try both on the real surface, and return what you don’t need.

Overhead and Safety-Critical Loads

Don’t rely on magnets alone where a fall could hurt someone, such as heavy items over a walkway or a bed. Add a mechanical fastener or safety cable.