2 x 1/2 Inch Strong Neodymium Rare Earth Countersunk Ring Magnet N52 (1 Pack)
2 x 1/2 Inch Strong Neodymium Rare Earth Countersunk Ring Magnet N52 (1 Pack)
| Quantity | Price | Discount |
|---|---|---|
| Buy 2 | $53.96/ea | 5% Off |
| Buy 3 | $51.12/ea | 10% Off |
| Buy 5 | $48.28/ea | 15% Off |
| Buy 10 | $45.44/ea | 20% Off |
| Buy 25 | $42.60/ea | 25% Off |
| Buy 50 | $39.76/ea | 30% Off |
| Buy 100 | $36.92/ea | 35% Off |
Magnet Specifications
| Imperial Size | 2.00 x 0.50 Inch (Outer Diameter x Thickness) |
|---|---|
| Metric Size | 50.8 x 12.7 mm (Outer Diameter x Thickness) |
| Countersunk Hole Size | 0.365 x 0.195 Inches at 82° |
| Countersunk Hole Location | Both Sides (Double Countersunk) |
| Screw Size | #8 |
| Material Grade | N52 |
| Pull Force | 118 lbs |
| Coating | Nickel-Copper-Nickel (Ni-Cu-Ni) |
| Magnetization Direction | Axially |
| Magnet Material | Sintered Neodymium (NdFeB) |
| Tolerance | +/- 0.004 Inches |
| Max Operating Temperature | 80°C / 176°F |
| Flux Density (Br) | 14,800 Gauss |
| Magnet Weight | 193.0 Grams |
| Part Number | DCS2X12N52 |
| Quantity Included | 1 Countersunk Ring Magnet |
Produced in an ISO 9001 Facility
Manufactured to Meet RoHS & REACH Standards
Installing Countersunk Magnets: Snug, Not Tight
Tighten each screw only until its head sits flush with the magnet, then stop. Neodymium is hard but brittle, so it can't flex like a steel washer. Once the screw head seats, every extra turn wedges it deeper into the countersink and can crack the magnet around the hole.
Use #8 flat-head screws. Avoid pan-head and round-head screws, which press on the thin edge of the hole.
Drive the screw by hand when you can. If you use a drill/driver, set the clutch to a low number, drive slowly, stop about one turn early and finish by hand. Don't use an impact driver or drill mode. Mount the magnet on a flat surface over a pilot hole, because a bump or glue drip underneath can crack it as you tighten.
Learn more:
How Do I Install Countersunk Magnets Without Breaking Them?
Can I Use Metric and Imperial Screws Interchangeably With Countersunk Magnets?
Magnet Safety Warning
Please use extreme caution when handling these 2 x 1/2 inch (Outer Diameter x Thickness) disc magnets. They are incredibly strong and powerful, and can pose a serious risk to your safety.
These large, grade N52 disc magnets are very difficult to separate and can snap back together with incredible speed and force. This may cause them to break and send small fragments flying into the air, potentially causing injury.
With 118 lbs of pull force, these disc magnets can also severely pinch your fingers if they snap back together. For your safety, keep these strong magnets far apart and at a safe distance of several feet or more once separated. Hand and eye protection is strongly recommended when handling these magnets.
- Magnet Safety Information
- RoHS/REACH Compliance
- 30 Day Return Policy
- Specification Sheet (PDF) (opens in a new tab)
- Technical Drawing (PDF) (opens in a new tab)
- 3D CAD Model (STEP)
Dimensions are nominal; see the drawing for tolerances. STEP files open in SolidWorks, Fusion, Onshape, FreeCAD and most other CAD software.

Featured product
Learning Center



